Give us a call! 405-912-5900

Interstate Heating and Air Conditioning has been the loyal provider of HVAC services in Oklahoma City, OK since 2002.  When your AC or furnace is not working, our pros can get your heating and cooling running again. We are experts when it comes to HVAC repair, Air conditioning replacement and all types of furnace services.

If you want to see why Oklahoma City, OK chooses us for heating and cooling when quality is needed, just have a look at our reviews.

With a heating and air conditioning tune-up in OKC–and with the right HVAC company you can expect:

  • Greater energy efficiency
  • Fewer breakdowns
  • Less costly repairs

All of this adds up to more money savings. Plus, you can expect higher quality heating and cooling. To take advantage of these benefits, call Interstate at (405) 237-4937.

Typically, if your heating and air system is making loud noise, something is wrong with it. If you are hearing hissing, banging, squealing, buzzing, clicking or any other obvious noise, you should call a trusted HVAC company for service. Interstate is available for convenient scheduling at (405) 237-4937.

The decision to repair or replace your AC system is dependent on:

  • Age – Is it over 15 years?
  • Energy costs – Are your energy bills slowly climbing?
  • Your comfort level – Are you still comfortable in your home?
  • Home additions – Have you added to your home?
  • And more

Get professional guidance on whether you need a replacement or repair by calling the HVAC pros at Interstate: (405) 237-4937.

AC tune-ups make sure your air conditioner is running optimally and can also help to extend the life of your unit. The cost to have your AC professionally serviced usually falls between $75-$200. You should have an AC tune-up scheduled once a year in the Spring to make sure it lasts you throughout the hot Summer.

You can count on the experts at Interstate Heating & Air Conditioning to deliver quick, expert AC tune-up services. Contact us for more information today!

There are a few ways you can tell if your thermostat has gone bad, including:

  • Your thermostat won’t turn on.
  • Your HVAC systems keep turning off and back on again.
  • Uneven temperatures from room to room.
  • Your thermostat is over 10 years old.

Interstate Heating & Air Conditioning can answer questions you have about your AC thermostat. Call us today and we’ll be happy to help!

There are a few reasons why your AC may not be turning on. Some of these include:

  • Dirty Air Filter
  • Tripped Circuit Breaker
  • Refrigerant Leak
  • Blown Fuse
  • Dirty Coils

No matter what the condition of your AC is, Interstate Heating & Air Conditioning can figure out what the problem is and fix it quickly. Call us today for expert AC repair services!

Local Reviews
for Oklahoma City, OK

Interstate Heating & Air Conditioning Rated 4.9 out of 5 stars based on 540 customer reviews


Excellent service!




Review of Interstate Heating & Air Conditioning


Great job with yearly furnace inspection




Review of Interstate Heating & Air Conditioning

Mike, the tech, was very nice and did a superb job.


Great service! Very efficient!




Review of Interstate Heating & Air Conditioning

Very detailed explanation of the problem.


Great service




Review of Interstate Heating & Air Conditioning

Courteous, knowledgeable and I do appreciate the quick service call.


Great Service




Review of Interstate Heating & Air Conditioning

Great job! On time! Efficient!


Great Service




Review of Interstate Heating & Air Conditioning


Great Service




Review of Interstate Heating & Air Conditioning


Tech was very professional.




Review of Interstate Heating & Air Conditioning

Explained everything he was doing for my benefit. Quite knowledgable knew his job completed in adequate time.


Great service!!




Review of Interstate Heating & Air Conditioning


Great service




Review of Interstate Heating & Air Conditioning


Great work




Review of Interstate Heating & Air Conditioning

Very professional team, on time and completed work as scheduled.


Happy




Review of Interstate Heating & Air Conditioning

Thanks for taking care of us and being quick to make repairs and always sending good quality workers to do the job!


Great job!




Review of Interstate Heating & Air Conditioning

I appreciated Chris’ ability to quickly understand the problem, resolve it and then explain the issue to me. He was very professional and easy to talk to. I would definitely use Chris and Interstate again!


Awesome job!




Review of Interstate Heating & Air Conditioning

Totally nice and helpful. Went above and beyond service


service was very good




Review of Interstate Heating & Air Conditioning

timely, knowledgeable, and reasonable


Great Service




Review of Interstate Heating & Air Conditioning


Appointment schedule was followed up email and phone prior to tech arriving. Great customer service!




Review of Interstate Heating & Air Conditioning


Great Service today, as usual with Interstate Heat & Air




Review of Interstate Heating & Air Conditioning


Great service




Review of Interstate Heating & Air Conditioning

Came in timely


Dedicated, friendly service.




Review of Interstate Heating & Air Conditioning

Great, came back at no expense to correct a problem that came up after the initial repair.


"top notch"




Review of Interstate Heating & Air Conditioning

were able to get to my problem right away. fix in no time. thank you.great service.


Great Service




Review of Interstate Heating & Air Conditioning

Mike did an excellent job. Explained everything clearly and was extremely helpful. Their scheduling and times were great and professional. I will definitely use them again.


Quick reliable service




Review of Interstate Heating & Air Conditioning

Jake showed up on time, was very friendly and gave me all of my options in a clear and concise manner.


Friendly Service




Review of Interstate Heating & Air Conditioning

They were very personable and did a great job of explaining everything.


Great service




Review of Interstate Heating & Air Conditioning

Technician was on time, friendly, and had the issue figured out fast.


Jason B.

Jason B.

16OCT2021 Jason B Arrived for for fall tune up. Spoke with Homeowner about systems performance. Cycled system on at thermostat then disconnect power at furnace. Pull blower motor and coil door inspect heat exhaust, capacitor and blower motor. Reinstall blower pull and clean flame sensor. Test all pressure switches, then reconnect power. Cycle system on in heating. Adjust gas pressure to 3.5 IWC. Inspect HSI, burners, and all safeties. Check amp draws, inducer, gas manifold, temperature split, and CO Levels. System is running properly at this time. I noticed some water spots on the wood under the flue, after speaking with the homeowner about it, the roof has been recently repaired. Inspected exterior flue, and found the cap and storm collar in good condition and sealed.

Near NW 31st St, Oklahoma City, OK 73112
Joseph K.

Joseph K.

I arrived for a previous customer no heat call. They are selling their home and the inspected the furnace and cycled it on by the thermostat. The system can on in heat and ran with no issues. I cycled the system on at the furnace and found it to be operational with no faults at this time.

Near S Broadway Ave, Oklahoma City, OK 73170
rodneys@interstateheatandair.com

rodneys@interstateheatandair.com

Non club tune up x 2. Main house. Furnace. Blower motor is ECM, no capacitor required, motor and wheel are clean, hot surface ignitor checked good, cleaned and checked flame sensor, pressure switch checked good, inducer motor run load amps are within mfg specs, all limits and safeties checked good, adjusted manifold pressure 4 in wc to 3.5 in wc to bring within mfg specs. Cycled system with stat and checked operation, no problems noted. Carbon monoxide was 0 ppm. System operating normally. Shop. Heat pump. Blower motor is ECM, no capacitor required. Checked heat strip operation, all sequencers operating normally, heat strip amps are good at 20A x 2. Heat pump. Replaced weak dual run capacitor, contactor is good. I initiated defrost, reversing valve shifted to cooling mode and condenser fan motor shut down. 1 minute later reversing valve shifted back to rest position and condenser fan motor resumed operation. All amps and pressures are good. Unit operating normally.

Near SE 99th St, Oklahoma City, OK 73165
Chris  D.

Chris D.

Arrived on 15 October for low airflow problem upon full inspection of ductwork found that the return duct is under size did you return duct system or 12 and they need to be 14s and the one going to the hallway goes from Flex to round metal and this one is smashed flat and it does not have a 1 foot extension past the end of this supply Plenum for proper static pressure gave customer an estimate for repair.

Near NW 89th St, Oklahoma City, OK 73132
Joseph K.

Joseph K.

I arrived for a new customer no cool call. I first spoke with the homeowner and found that the furnace will not run and they want it looked at. I inspected the furnace and the condenser and found the system to come on and run properly. The induced draft motor in the furnace is spinning the bearings on the motor and has play to it. I also found the heat extremely to have excessive rust on the heat expand the collective box. I inspected the heat exchanger and found no cracks at this time. I checked the co levels and found no readings at this time. I recommended to have some carbon monoxide detectors installed in the home due to the poor condition of the furnace and ac system. I recommend to replace the system before make any repairs on the system due to cost of repair vs replace. The homeowner decided to just let the system run as long as it can before replacing the system. We will need to send the homeowner a receipt. Jake Kring.

Near NE 33rd St, Oklahoma City, OK 73111
rodneys@interstateheatandair.com

rodneys@interstateheatandair.com

Silver club fall service. Blower motor is ECM, no capacitor required, motor and wheel are clean, condensate drain is clear, hot surface ignitor checked good, cleaned and checked flame sensor, pressure switch checked good, inducer motor run load amps are within mfg specs, all limits and safeties checked good, inducer motor run capacitor checked good, manifold pressure is 3.5 in wc, within mfg specs, air temperature rise was 47 deg, within mfg specs. Carbon monoxide 0 ppm. Carbon monoxide detector by tstat checked good. System operating normally.

Near Blue Bonnet Dr, Oklahoma City, OK 73159
Mike T.

Mike T.

On October 15, 2021 arrive to a Blue Shield customer for a full tuneup upon arrival agree to the customer are then as the customer to turn the thermostat to heat and turn it up since everybody in the house was still asleep and she didn’t want me in there I think climbed in the attic did amp draw‘s on the inducer motor pool and clean the flame sensor didn’t draw only hot surface igniter I then checked the capacitor on the blower did amp drawls on the blower checked temp rise and change the filter everything‘s working properly at this time thank you for your business Mike T

Near Cypress Dr, Oklahoma City, OK 73170
rodneys@interstateheatandair.com

rodneys@interstateheatandair.com

Blue shield fall service. Replaced filter. Blower motor run capacitor checked good,motor and wheel are clean, condensate drain is clear, hot surface ignitor checked good, cleaned and checked flame sensor, pressure switch checked good, all limits and safeties checked good, manifold pressure is 3.5 in wc, within mfg specs, inducer motor run load amps are within mfg specs, air temperature was 36 deg, within mfg specs. Carbon monoxide was 0 ppm. System operating normally.

Near NW 47th St, Oklahoma City, OK 73118
ISAAC J.

ISAAC J.

Came out to give estimate for replacement of HVAC equipment. Went over options with customer and gave him a few estimates to choose from based on what was discussed. Special Financing or discounts available with estimates chosen. Please call if you have any questions! Thank you for choosing Interstate Heat and Air for an estimate to help you stay comfortable year round.

Near SW 154th Ct, Oklahoma City, OK 73170
Mike T.

Mike T.

On October 14, 2021 I arrive to a Silver club member for a full tuneup upon arrival agreed the customer and then went to the thermostat turn the system to heat and turned it on and then went to the furnace did amp draw‘s on the inducer motor check the capacitor for the motor are there and didn’t draws on the blower motor there is no capacitor on the blower I then pulled and cleaned the flame sensor did amp drawls on the hot surface igniter checked gas pressure no adjustment needed poured and changed to 14 x 24 x 1 filters and a 12 x 12 x 1 filter everything ‘s working properly at this time thank you for your business Mike T

Near Bluewater Rd, Oklahoma City, OK 73165
Chris  D.

Chris D.

Right on 14 October for a furnace tuneup change removed cleaned and reinstall flame sensor remove Cleaned and reinstalled Sparket nighter check temperature rise gas pressure Change filter check blower everything is running within manufacture specifications

Near NW 27th St, Oklahoma City, OK 73107
Joseph K.

Joseph K.

We arrived to service 6 package units and 1 mini split. All systems are labeled 2 - 7 and the mini split in not labeled. All thermostat are labeled a according to there thermostats that operates the system. System labels #1 is not a system to be serviced. They have 7 units in total. System 3 and 4 both need Induced draft motors.

Near W Memorial Rd, Oklahoma City, OK 73134
Mike T.

Mike T.

On October 14, 2021 I arrive to a Blue Shield customer for a furnace tuneup upon arrival agree to the customer then went to the thermostat turned it to heat and turned it up I then went to the furnace I did amp drawls on the inducer motor check the capacitor on the inducer motor is good I then pulled and cleaned the flame sensor check the gas pressure it was at 4.7 I dropped it down to 3.2 I then did amp drawls on the blower motor and check the capacitor it was a 10 µF equal 8.4 µF it is out of tolerance recommended replacement customer declined at this timeCheck the hot surface igniter everything except for the capacitor is working properly thank you for your business Mike T

Near Cedar Valley Dr, Oklahoma City, OK 73170
rodneys@interstateheatandair.com

rodneys@interstateheatandair.com

Blue shield fall service. Replaced filter. Blower motor is ECM, no run capacitor required, motor and wheel are clean, hot surface ignitor checked good, cleaned and checked flame sensor, pressure switch checked good, inducer motor run load amps are within mfg specs,, all limits and safeties checked good, manifold presssure is 3.5 in wc, air temperature rise was 38 deg, within mfg specs. Cycled system with tstat. System operating normally. Carbon monoxide, 0 ppm

Near SW 99th Pl, Oklahoma City, OK 73139
rodneys@interstateheatandair.com

rodneys@interstateheatandair.com

Silver club fall service. Blower motor run capacitor checked good, motor and wheel are clean, hot surface ignitor checked good, cleaned and checked flame sensor, inducer motor run load amps are within mfg specs, pressure switch checked good, manifold pressure is 3.5 in wc, within mfg specs, air temperature rise was 44 deg, within mfg specs. Carbon monoxide was 0 ppm. System operating normally

Near Falcon Pl, Oklahoma City, OK 73162
Jason B.

Jason B.

13OCT2021 Jason B Arrived for call about burnt or chewed wiring, spoke with homeowner about issue, when shown the cable in question I found that it is coax. It looks like there was previously a home theater setup in the atrium. This wire has nothing to do with your hvac system and the system is safe to run. It was neat meeting you guys have a safe week and great Halloween as well!

Near Davis Ct, Oklahoma City, OK 73162
rodneys@interstateheatandair.com

rodneys@interstateheatandair.com

Arrived for a no cool, evalueated system and found common terminal and wire melted off on dual run capacitor. With homeowner ok I replaced dual run capacitor and repaired 2 wires. Checked system operation, no other problems found. System operating normally.

Near SW 30th St, Oklahoma City, OK 73179
Joseph K.

Joseph K.

I arrived for a recall on a system we have been having water problems with. I inspected the system and removed the inspection doors on the air handler. I used a level and found the system to be leaning to the back right corner and overflowing the system causing the system to leak water into the secondary drain pan. The secondary drain pan has been bent and rusted through allowing water to leak out onto the decking of the porch. To fix this issue and to help prevent the problem from happening agin I recommended to relevel the air handler and replace the drain pan with a new pan. We would reuse the air handler and level the system to drain properly. Leaving the system in the shape it is in now is going to further damage the system and the decking. We cleaned the drain and added a P trap to the system to help the system drain properly in the past. I recommend to relevel the system and replace the secondary drain pan.

Near S Quapah Ave, Oklahoma City, OK 73119
Joseph K.

Joseph K.

I first spoke with the homeowner about what problems they were having. The min issue is that at times the system is blowing a fuze inside the hot tub. The way they have been getting by is by replacing the fuse and letting the system run. I then Inspected the system and found M#of heat pump PAXRW015/60HZ s# B011806270010. Water temperature is 95 deg Superheat in heating is at 26 deg. Water temperature at 98 deg Superheat in cooling is at 30 deg. Air temperature drop on condenser as the system is heating is 19 deg. Air temperature rise on condenser in cooling is 17 deg. Amp draw on compressor is 4.3 and max amps the compressor is 5.1. Amp draw on condenser fan motor is 2.9 and max amp draw is 3.9 amps. I cycled the system in all modes and found the system to respond to all commands given from the main controller.

Near W Wilshire Blvd, Oklahoma City, OK 73116
rodneys@interstateheatandair.com

rodneys@interstateheatandair.com

Blue shield fall service. Blower motor run capacitor checked good, motor and wheel are clean. At homeowners request I replaced thermocouple, relit pilot light and checked operation. Manifold pressure 9.5 in wc, propane system. Blower motor run load amps within mfg specs, air temperature rise is 35 deg,. Carbon monoxide 0ppm. Home owner does not have a carbon monoxide detector. Strongly recommend that he purchase one.. system operating normally.

Near SE 149th St, Oklahoma City, OK 73165
Mike T.

Mike T.

On October 12, 2021 I arrive to a new customer nonmember upon arrival agree to the customer they stated that they were having a power outage and that the outdoor unit wasn’t coming on upon further inspection found that there was a bug in the contactor causing it not to pass voltage cleaned out the bug put the disconnect in and the system started running immediately I did amp draw‘s on the compressor and the fan motor check the capacitor and check the charge everything‘s working properly at this time thank you for your business if you have any further issues please give us a call so we can get you taken care of Mike T

Near SW 85th St, Oklahoma City, OK 73139
Mike T.

Mike T.

On October 12, 2021 I arrive to a white showed customer for a full tuneup upon arrival agreed the customer then went to the thermostat turn the system to heat and turn turned it up I then went up to the furnace pulled and cleaned the flame sensor to check the gas pressure it was at 4.1 dropped it down to 3.2 I did amp drawls on the inducer motor I checked the capacitor did amp drawls on the blower motor did amp draws on the hot surface igniter tested temp rise and then changed out two 14 x 24 x 1 filters and a 12By 12 x 1 filter everything’s working properly at this time thank you for your business Mike T

Near Shorehan Ct, Oklahoma City, OK 73170
Jason B.

Jason B.

12OCT2021 Jason B Arrived for two system fall maintenance. Spoke with Melani about systems performance, we haven’t ran the heating this season. Inspected trane system first. Cycled system on at thermostat then disconnected power at furnace. Pull blower motor and coil door inspect heat exchanger, capacitor and blower motor. Capacitor reading 19.9/20 Reinstall blower. pull and clean flame sensor. Test all pressure switches, then reconnect power. Cycle system on in heating. Adjust gas pressure to 3.5 IWC. Inspect HSI, burners, and all safeties. Check amp draws, inducer gas manifold, temperature split, and CO Levels. Downstairs system Cycled system on at thermostat then disconnect power at furnace. Pull blower motor inspect heat exchanger, and blower motor. Reinstall blower pull and clean flame sensor. Test all pressure switches, then reconnect power. Cycle system on in heating. Adjust gas pressure to 3.5 IWC. Inspect HSI, burners, and all safeties. Check amp draws, inducer, gas mani

Near Fairway Ave, Oklahoma City, OK 73170
Chris  D.

Chris D.

Arrive on 12 October for a fall tuneup silver club to gas pressure readings it is at 3.489 inches of water column measured heat rise it was at 40° manufacture specifications states 30 to 60 removed cleaned and reinstalled measured flame sensor after cleaning flame sensor is sitting at 4 DC millivolts check blower checked heat exchanger measured hot surface igniter it was at 48 ohm’s customer changes on filters. Inspected flu and induced draft motor system is running within manufacture specifications at this time. Thank you for your business Chris.

Near Remington Way, Oklahoma City, OK 73134
rodneys@interstateheatandair.com

rodneys@interstateheatandair.com

Blue shield fall service. Home owner had already replaced filter, left 1 filter. Blower motor is ECM, no run capacitor is required, motor and wheel are clean, indoor coil is clean, spark ignitor operates normally, pressure switch checked good, all limits and safeties checked good, inducer motor run load amps are good, manifold pressure is at 3.5 in wc, within mfg specs, air temperature rise is 39 deg,within mfg specs. Carbon monoxide 0pmm. System operating normally

Near SW 48th St, Oklahoma City, OK 73119